Home
JAQForum Ver 24.01
Log In or Join  
Active Topics
Local Time 11:11 24 Apr 2026 Privacy Policy
Jump to

Notice. New forum software under development. It's going to miss a few functions and look a bit ugly for a while, but I'm working on it full time now as the old forum was too unstable. Couple days, all good. If you notice any issues, please contact me.
Forum Index : Windmills
  Topics Started By Replies Views
Last Post By
Sticky Topics        
Forum upgrade Gizmo, 05/07/2019 314 201685 wiseguy  04:07am 12 Dec 2025
Forum Guidelines Gizmo, 11/12/2011 2 518364   02:49pm 16 Dec 2015
Normal Topics  

   Page 30 of 99    

VAWT WALL rissole, 10/07/2011 1 3945   10:22pm 10 Jul 2011
White Pointer AXFX Trev, 05/01/2011 55 55513   03:16pm 10 Jul 2011
PhillM dual kicking butt for KarlJ! KarlJ, 10/07/2011 2 3712   01:24pm 10 Jul 2011
Wind turbine noise solution barrygun, 03/07/2011 10 6898   04:28pm 09 Jul 2011
Little help please i8unwo, 29/06/2011 3 4864   01:00pm 09 Jul 2011
Going were no turbine has gone before Tow BobMann, 09/07/2011 2 4282   12:38pm 09 Jul 2011
An answer if I may Smokey5159, 09/07/2011 3 4240   12:40am 09 Jul 2011
inverterless solution vawtwindy, 04/07/2011 3 4464   09:06am 04 Jul 2011
Vawt - grid / mains connection Ynot, 03/07/2011 6 4250   09:02am 04 Jul 2011
cutting Magnets brucedownunder2, 07/06/2011 6 5700   11:47pm 02 Jul 2011
To re-wire or not re-wire Smokey5159, 02/07/2011 3 3739   11:10pm 02 Jul 2011
Simple Windmill/Solar controller bertech, 27/06/2011 3 3629   01:48pm 01 Jul 2011
What set-up? Smokey5159, 28/06/2011 5 4919   04:00pm 30 Jun 2011
Installation red tape Rastus, 24/06/2011 17 5784   02:20pm 30 Jun 2011
2 Stage Cutin Coils Idea. Downwind, 31/10/2010 19 18235   11:21am 28 Jun 2011
Chinese Ouyad Electronics Ltd 2Kw WT jimisbell, 28/06/2011 0 3105   05:13pm 27 Jun 2011
MacGyver Ax-Fx Build MacGyver, 19/05/2010 119 99899   02:39pm 27 Jun 2011
EMC Compliance required? darcyrandall200, 19/06/2011 6 4236   07:14am 26 Jun 2011
Voltage controllers paul_mac1, 25/06/2011 2 3402   11:50pm 25 Jun 2011
Senate inquiry Jarbar, 09/02/2011 3 5319   11:20am 22 Jun 2011
DIY?? petanque don, 09/09/2010 24 18100   03:22pm 21 Jun 2011
Dual F&P Mill stop Rastus, 10/02/2011 23 12629   02:00pm 21 Jun 2011
new geared wind machine. fixitguy, 12/06/2011 9 4997   12:03am 18 Jun 2011
F&P won’t spin on 12 v system GaryP, 10/06/2011 12 5974   12:31am 15 Jun 2011
Coroflute Blades MacGyver, 31/05/2010 41 45886   06:25pm 14 Jun 2011
= New posts since you last visited .      

   Page 30 of 99    

The Back Shed's forum code is written, and hosted, in Australia.
© JAQ Software 2026